Skc DataTrac for the Leland Legacy Manual de usuario Pagina 1

1Cat. No. 877-92Operating InstructionsSKC Inc.863 Valley View RoadEighty Four, PA 15330 USATel: 724-941-9701e-mail: [email protected] 40085 Rev 1

7SKC DataTrac Pump ManagerSKC DataTrac Pump ManagerThe SKC DataTrac Pump Manager window (Figure 4) is the fi rst window that opens in DataTrac. All win

8SKC Real Time MonitorA. Real Time Monitor Display (page 9) B. Flow Calibrate Bu ons (page 10) C. Temperature Display (page 12)D. Pressure Di

9SKC Real Time MonitorPump Real Time Monitor DisplayThe Real Time Monitor display (Figure 6) shows the operating status of the connected pump. Pump St

10SKC Real Time MonitorBattery Selection ButtonsThe Ba ery Selection Bu ons (Figure 7) allow the user to select the battery that is installed in the

11SKC Real Time MonitorSet the pump to 10 L/min. If the calibrator displays 9.7 L/min, click the  bu on in Flow Calibrate until the calibrator displ

12SKC Real Time MonitorTemperature DisplayThe Temperature Display (Figure 11) shows the temperature of the air entering the connected pump.Cell Read

13SKC Real Time MonitorFigure 12. Pressure DisplayFigure 13. Pump Controls ButtonsFigure 11A. Reset Volume, Temp, Run Time, and Pressure ButtonPressur

14SKC Real Time MonitorFigure 14. Units Selection ButtonsFigure 15. Fault OptionsUnits Selection Buttons The Units Selection bu ons (Figure 14) allow

15STEL/Timed RunFigure 16. STEL/Timed Run WindowSTEL/Timed RunThe STEL/Timed Run window (Figure 16) allows the user to set a pump run for a predetermi

16SKC Pump SchedulerBACEFGFigure 17. Pump Scheduler WindowDHISKC Pump SchedulerThe SKC Pump Scheduler window (Figure 17) is the DataTrac programming w

Table of ContentsIntroduction ... 1DataTrac Setup ...

17SKC Pump SchedulerFigure 18. Program Edit Bar Pump Scheduler Menus File MenuOpen ...opens a pump program previously store

18SKC Pump SchedulerFigure 19. Pump Schedule Containing ProgramsFigure 20. Programming Buttons Pump ScheduleThe Pump Schedule (Figure 19) contains pum

19SKC Pump SchedulerFigure 22. Program Loaded Dialog BoxFigure 21. Confi rmation Dialog BoxFigure 23. Leland Legacy with ProgramInsert ButtonTo insert

20SKC Pump SchedulerFigure 25. Scheduler Set Flow WindowFigure 24. Set Flow ButtonFromPump ButtonTo display a Pump Schedule from a previously programm

21SKC Pump SchedulerFigure 27. ClockFigure 29. Select 4:15Figure 28. Clock ResolutionClick hereFigure 26. CalendarCalendarThe Calendar (Figure 26) sho

22SKC Pump SchedulerFigure 32. Time Bump all Dates ButtonsFigure 30. Digital Time DisplayFigure 31. Select Time DisplaySelecting a Time Using the Digi

23SKC Pump SchedulerFLOWL / minsLelandLegacyFigure 33. Date/Time Display WindowFigure 34. Clear History MessageDate/Time DisplayTo access the Date/Tim

24SKC Pump SchedulerFigure 35. Scheduler OptionsScheduler OptionsTo access the Scheduler Options window (Figure 35) in the SKC Pump Scheduler, go to t

25SKC Pump SchedulerFigure 36. Cycle SchedulerCycle SchedulerTo access the Cycle Scheduler window (Figure 36) in the Pump Scheduler, go to the View me

26SKC Pump SchedulerFigure 37. Repeat SchedulerRepeat SchedulerTo activate the Repeat Scheduler (Figure 37), go to the Repeat Schedule cell in the Pum

2

27Example Scheduler ProgramClick hereClick hereExample Scheduler ProgramThis example program demonstrates step-by-step how to use the SKC Pump Schedul

28Example Scheduler ProgramTo insert the program into the Pump Scheduler:Click on the Insert bu on. The program appears in the Pump Schedule. Note t

29Example Scheduler ProgramRepeat SchedulerIf the user wishes to repeat the example schedule for the next 10 weeks, the Repeat Scheduler could be used

30Example Scheduler ProgramTo set the desired Scheduler Options:Select Scheduler Presets from the View menu and click on the desired Scheduler Options

31SKC Pump HistoryFigure 38. SKC Pump History WindowSKC Pump HistoryThe SKC Pump History window (Figure 38) displays a record of all operations the pu

32SKC Pump HistoryClear Pump HistoryTo clear the pump history, select Clear History from the Tools menu.Change Options*To change display and sample in

33SKC Pump History User Setup ...pump user interface accessed and user adjusting pump Pre-Cal Flow ...single-point calibration mode

34Archive HistoryArchive HistoryThe Archive History window loads and displays a pump history fi le that was saved to a PC. This window is empty until a

35ReportsFigure 39. Sample Sheet Setup WindowReportsDataTrac allows reports or worker exposure profi les to be printed or saved as text and imported in

36ReportsFigure 40. Close-up of the Sample Sheet Setup Window Showing Active Check BoxesLoad Template ...loads a template fi leSave Template ...sa

1IntroductionIntroductionDataTrac Software for Leland LegacyFeatures• Program a sampling operation from a PC• Calibrate pump fl ow to a primary standa

37ReportsSave TemplateTo save only the information contained in data cells with active check boxes, select Save Template from the File menu. The Save

38ReportsFigure 41. Calibration Info WindowCalChek Full Calibration Data Display and Verifi cationViewing CalChek Full Calibration Data Caution: Full c

39ReportsFigure 42. Calibration Info Window with Confi rm Validation CodeValidating CalChek Full Calibration DataTo confi rm printed calibration data, o

40- Button ... 22+ Button ... 22+Day Button ...

41Printing Programs ... 20 Reports ... 37 Sample Sheet Setup...

2DataTrac SetupDataTrac SetupInstalling DataTrac SoftwareInstallation of New Software1. Close all applications.2. Insert DataTrac So ware CD into C

3DataTrac SetupIf changes to se ings are desired a er installation, perform Steps 1 through 4 below. The IS Program Maintenance window will displa

4DataTrac SetupFigure 2. Connection WindowConnecting the Pump to a PC (Figure 1)USB port on PC: Use the supplied adapter cable to connect the pump to

5DataTrac SetupFigure 2B. Connection Error BoxSuccessive Connections 1. Connect the pump to a PC using the DataTrac adapter cable.2. Activate the pu

6DataTrac Setup6. If the date and time settings on the PC and pump differ by a day or more than 5 minutes, respectively, a Time Discrepancy Alert win